Fitting The 1911 Barrel Part 2: Bottom Lugs

Fitting The 1911 Barrel Part 2: Bottom Lugs

As we've noted before, the most important factor in 1911 accuracy is barrel fit. In the last article we fitted the hood, and in this one we delve into the fit of the bottom lugs to the slide stop. When the slide is in battery, the barrel should be wedged between the slide stop and the locking grooves in the slide with zero movement. In fact, if you function the pistol by hand without the recoil spring, you should feel a slight resistance as the barrel locks.

The lugs on our Kart barrel are oversized and must be cut to fit the slide stop. Fitting can be done by hand with files and stones (very time consuming), with a hand-turned lug cutter such as sold by Brownell's (080-000-068WB) or with machine tools.

I used a manual lug cutter for many years before I had a milling machine and they work fine, but there is no control over the size of cut. You get a .195" or .186" cutter and they have to work. I believe machining the lug with a dedicated fixture is the best way and that is how I do it now.

We begin by verifying the size of the slide stop pin. Check the size of the hole in the frame with pin gauges. The Colt frame I'm using for this demo is .202" and our new Ed Brown slide stop is .200". That fit is reasonable. Slide stops are available with pin diameters up to .203" for worn frames. Use the largest pin that will fit the frame and still rotate freely.


Install the barrel and Kart bench bushing in the slide and assemble it to the stripped frame without the slide stop. You will need pin gauges in sizes ranging from .180" to .200". Insert a .180" pin gauge in the slide stop hole and try to move the slide forward into battery.


If the barrel locks up on the pin, keep trying larger pins until you reach the largest size that will allow lockup. Let's say the largest pin the pistol accepts is .180". OK, that means you've got to remove .020" of material from the lugs for them to lock up on your .200" slide stop pin. Remove the barrel and take it over to the milling machine.

In our mill vise we have the Weigand barrel fitting fixture. This tool allows the barrel to be clamped in a V-block while the lugs are milled to size and the barrel can be removed for checking fit and returned to the fixture without loss of zero.

The bottom of the fixture has a step milled into it so cutting is done at the proper lockup angle. A digital readout is highly recommended when using this fixture. The cutter we have mounted in our mill collet is a four-flute HSS 5mm end mill (closest size available to our .200" slide stop diameter). Take a test cut, removing a few thousandths of material from the lugs.

Now we reassemble the slide, barrel and bushing to the frame and select the largest gauge pin that will allow the barrel to lock up, let's say .184" in this case.


An important check at this point is determining if both lugs are bearing on the pin equally. Blacken the .184" gauge pin with a marker, install it in the frame, function the slide a few times and remove it. Good contact by both lugs should be visible on the pin.

If not, adjust the jack screw under the barrel lugs on the Weigand fixture so the cut is slightly heavier on the lug that shows the most contact and take another test cut. Repeat this process as necessary to produce even contact by both lugs. When lug contact is correct, continue cutting until the lugs will lock up on a .196" or .197" pin.

Now, reduce your cuts to only .001î at a time until the barrel will lock on the slide stop with just a bit of thumb pressure applied to the rear of the slide. Finish fit with lapping compound and you should be done.


Judge the length of cut with the thumb safety when the barrel is locked up. It should easily enter the notch in the slide without a big gap at the front. If you are fitting the barrel to the original slide that came with the pistol, the rear edge should be even with the edge of the frame. If you are using a new slide, it may have to be dressed off after the barrel is fitted so there is no overhang.

Our barrel is not completely fitted yet. We still have to finish cut the chamber and install a bushing. Stay tuned for part 3.

Tools

Here are the tools needed for successful barrel lug fitting on a 1911: pin gauges from .180" to .200", calipers, Kart bench bushing and a marker.

Slide stop shaft measures

The slide stop shaft measures .200". If it won\'t fit easily, you\'ll need to open up its hole in the lug until it operates correctly, without binding.

Weigand lug barrel fitting fixture

The Weigand lug barrel fitting fixture. . This tool allows the barrel to be clamped in a V-block while the lugs are milled to size with a milling machine.

Lugs

To test fit the barrel lugs with a gauge pin, first blacken the gauge pin with a marker to check lug contact. Note the good contact here from both lugs.

Lugs

To test fit the barrel lugs with a gauge pin, first blacken the gauge pin with a marker to check lug contact. Note the good contact here from both lugs.

Lugs

To test fit the barrel lugs with a gauge pin, first blacken the gauge pin with a marker to check lug contact. Note the good contact here from both lugs.

Cutting Lugs

Cutting the lugs with a 5mm end mill and the Weigand fixture. A digital readout for the X and Y axis is highly recommended for getting the very best cut.

Digital Readout

Cutting the lugs with a 5mm end mill and the Weigand fixture. A digital readout for the X and Y axis is highly recommended for getting the very best cut.

Thumb Safety

The fit of the thumb safety will help you judge the length of your cut. It should easily fit into its slide notch without a gap at the front edge.

Rear of the slide

The rear of the slide should be close to even with the rear of the frame when the thumb safety fits correctly in its notch. Don\'t cut any farther here.

Perfect fit

A perfect fit. Note the even lug contact on the slide stop after lapping. Both legs of the lug need to tough the slide stop evenly for best accuracy.

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Recommended Articles

See More Recommendations

Popular Videos

New handguns from Smith & Wesson

New handguns from Smith & Wesson

The Performance Center's M&P380 Shield EZ pistol features ported barrel, flat face trigger and tuned action.

American Suppressor Association (ASA)

American Suppressor Association (ASA)

ASA is the unified voice of the suppressor industry and a leading subject matter experts on suppressors and suppressor related advocacy.

New addition to the Browning X-Bolt rifle series

New addition to the Browning X-Bolt rifle series

New for 2019 is the Max Long Range model featuring a composite Max stock with fully adjustable comb, spacers for adjusting length of pull, stainless fluted heavy sporter barrel, threaded muzzle brake and extended bolt handle.

Springfield Armory Saint Victor in .308

Springfield Armory Saint Victor in .308

The Saint Victor in .308 features a 16" light weight barrel, M-Lok® free float hand guard and included flip-up sights.

See More Popular Videos

Trending Articles

Rhode Islanders are setting brushfires for freedom once again as they advance a Second Amendment Sanctuary Town movement. 2nd Amendment

SPECIAL REPORT: BIG 2A HISTORY BEING MADE IN LITTLE RHODE ISLAND

John Peterson - May 22, 2019

Rhode Islanders are setting brushfires for freedom once again as they advance a Second...

Want the “Holy Grail” of AR-15 rifles? Brownells has made that possible with their BRN-Proto retro rifle. Rifles

Brownells BRN-Proto Retro Rifle

Patrick Sweeney - July 02, 2019

Want the “Holy Grail” of AR-15 rifles? Brownells has made that possible with their BRN-Proto...

If you want to keep the peace, keep and bear arms. Don't give up your guns. Any other choice would be ridiculous. 2nd Amendment

Is Red Dawn Really Just Ridiculous? If Not, Who Would Citizen Disarmament Help?

David Codrea - May 29, 2019

If you want to keep the peace, keep and bear arms. Don't give up your guns. Any other choice...

This will be the first of many investigative reports about the NRA by Firearms News. 2nd Amendment

Firearms News Investigates the NRA: Part 1

Nedd Scott - July 18, 2019

This will be the first of many investigative reports about the NRA by Firearms News.

See More Trending Articles

More Handguns

New Wilson Combat X-TAC and X-TAC Elite Commander-Size 1911s Handguns

New Wilson Combat X-TAC and X-TAC Elite Commander-Size 1911s

Wilson Combat - October 28, 2019

New Wilson Combat X-TAC and X-TAC Elite Commander-Size 1911s

Due to the popularity of the SAINT Victor and SAINT Edge pistols, Springfield Armory has announced the new SAINT Pistol chambered in 5.56mm NATO. Handguns

Springfield SAINT 5.56 Pistol Announced

Firearms News Digital Staff - October 14, 2019

Due to the popularity of the SAINT Victor and SAINT Edge pistols, Springfield Armory has...

Firearms News editor Vincent DeNiro runs the SCCY CPX-4 through a simple self-defense drill that you can try next time you are at the range. Handguns

Firearms News Looks at the SCCY CPX-4 in .380 (Video)

Vincent L. DeNiro, Editor - November 06, 2019

Firearms News editor Vincent DeNiro runs the SCCY CPX-4 through a simple self-defense drill...

Smith & Wesson is expanding their award-winning M&P Shield EZ pistol series to include the new M&P9 Shield EZ, chambered in 9mm. Handguns

Smith & Wesson Announces M&P9 Shield EZ

Firearms News Digital Staff - December 11, 2019

Smith & Wesson is expanding their award-winning M&P Shield EZ pistol series to include the new...

See More Handguns

GET THE MAGAZINE Subscribe & Save

Temporary Price Reduction.

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW OUR CURRENT ISSUE

GET THE NEWSLETTER Join the List and Never Miss a Thing.