Skip to main content

Squaring the AR Receiver Face

Squaring the AR Receiver Face

You've ordered a few tools from Brownells and you're assembling an AR from parts. It can be a lot of fun to build your own rifle and there are plenty of online tutorials and books available to show you how to do it. When it comes time to torque the barrel nut, you find that you have to really struggle to line up the gas tube hole.

If you loosen the nut to the previous hole, it seems too loose and if you apply a cheater bar to your wrench it feels like you're over-torqueing the nut. The problem could be that the face of the upper receiver isn't square or there is a burr so the nut feels like it's tight but the barrel shoulder is really only bearing on a small percentage of its seat.

Not to worry. Armorers long ago figured out a simple way to square the receiver face. We turned a piece of round stock to a diameter just shy of an inch so it would slide into the receiver and left a square shoulder that is used to apply lapping compound to the receiver face. A half-inch diameter cylinder is machined opposite the shoulder so the tool can be turned with an electric drill.

If you don't have a lathe you can buy one of these tools from Brownells (part #080-000-182) for $35. I have a lapping tool I made in the early 1990s that is very similar to the current Brownells product.


Secure the upper receiver in a vise. I used a Precision Reflex upper receiver vise block (714-000-006) to hold the one in the pictures. Lubricate the main shaft of the tool and make sure it will rotate freely in the upper receiver.


Apply lapping compound to the shoulder of the tool. Brownell's recommends 180-grit but the coarsest grade I had on hand was 500-grit and it worked fine. Try not to get any compound down into the receiver. Turn the tool with a drill, checking your work periodically and replacing compound as necessary.

Starting out you will notice that only a portion of the receiver face is turning silver as the anodizing is worn away. That is the high spot we are going to remove. Keep working until the entire ring is silver and smooth. Clean up the receiver and try torqueing the barrel nut again. Easier, isn't it? The barrel shoulder is now bearing evenly on the receiver face the way it should be.

Squaring tool

Norcross made his own squaring tool in the 1990s (top). The Brownells version below it gets the same job done, and you can buy one for about $35.

Squaring tool

Insert the lubricated pilot of the tool into the receiver and apply lapping compound to the tool's working surface. Don't get it inside the receiver.

Secure the receiver

Secure the receiver in a vise and drive the tool with a drill motor to lap the receiver face. Check periodically and replace compound when needed.

High spot

After some lapping, it's easy to see the high spot on the receiver that is preventing the barrel nut from snugging down to its proper final position.

Finished receiver face

The finished receiver face is smooth and square. Now it will be easy to turn the barrel nut to proper orientation. The gas tube will fit right through.

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Recommended Articles

Popular Videos

DL Sports SLR 762 Carbine

DL Sports SLR 762 Carbine

Patrick Sweeney tests out the DL Sports SLR 762 Carbine, an AK47 has been refined and civilized by Dave Lauck and DL Sports.

Firearms News Reviews the S&W M&P 2.0 9mm Compact Pistol

Firearms News Reviews the S&W M&P 2.0 9mm Compact Pistol

Firearms News editor Vince DeNiro runs the Smith & Wesson M&P 2.0 9mm compact pistol through a self-defense drill.

See All Videos

Magazine Cover

GET THE MAGAZINE Subscribe & Save

Digital Now Included!

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW OUR CURRENT ISSUE

Buy Digital Single Issues

Don't miss an issue.
Buy single digital issue for your phone or tablet.

Buy Single Digital Issue on the Firearms News App

Other Magazines

Special Interest Magazines

See All Special Interest Magazines

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Get the top Firearms News stories delivered right to your inbox.

Phone Icon

Get Digital Access.

All Firearms News subscribers now have digital access to their magazine content. This means you have the option to read your magazine on most popular phones and tablets.

To get started, click the link below to visit mymagnow.com and learn how to access your digital magazine.

Get Digital Access

Not a Subscriber?
Subscribe Now